(11) 2088-5701
DRYKOMANTA ALUM GLASS
1 m - 10 m
Industrialized waterproofing asphalt blanket made from modified asphalts with elastomeric polymers, reinforced with a reinforced, flexible glass fiber veil, tensile and tear resistance. Self protected with aluminum film on its exposed face which features high reflection of UV rays.
Indicated for:
- Areas with low structural movements;
- Roof slabs up to 200 m²;
- Roofs;
- Industrial kitchens.
The substrate for application of DRYKOMANTA ALUM GLASS must be clean, free of foreign bodies, form remains, iron tips, remnants of mold release or impregnating products, flaws and nests. In smooth concrete, sand with a steel brush or mechanically to open porosity and remove release agents or curing agent.
Carry out regularization with a minimum drop of 1% towards the water drainage points for external areas and 0.5% for internal areas, prepared with cement mortar and medium sand 1: 4 trace, adding DRYKOFIX adhesive emulsion in the water of kneading for greater adherence to the substrate. The mortar must be finished with a minimum thickness of 2 cm.
Round sharp corners and edges. It is worth mentioning that lime should not be placed in the leveling mortar.
Emerging pipes and drains must be rigidly fixed. A 1 cm deep drawdown around the drains with a diameter of 50 cm is recommended.
In the building entrance gaps (doors, frames, etc.), the leveling should advance at least 60 cm inwards, under jambs and underframe, respecting the trim for the external areas, except for internal areas with floors in wood or degradable by moisture. It is recommended that the external areas have a dimension of at least 6 cm less than the internal dimensions, both at the level of waterproofing and at the level of the finished floor.
Primer application
Apply one coat of DRYKO PRIMER ACQUA or DRYKOPRIMER ECO and wait for drying for
at least 6 hours before bonding the blankets and treating the drains and tubes.
Blanket application
Fully unroll the first blanket in the center of the area, leaving it aligned and then roll it up again. Secure the blanket using the chosen application system.
Torch application
With the aid of the torch, direct the flame on the side of the DRYKOMANTA ALUM GLASS that will be set on the substrate, make sure that the flame simultaneously heats the printed substrate and the DRYKOMANTA ALUM GLASS
Press from the center to the ends to remove excess and possible air bubbles.
The floor covering should rise 10 cm at the bottom and the floor covering should overlap the floor covering by 10 cm. In emergent drains and pipes, reinforcement should be performed with a blanket strip.
Valid for 60 months from the date of manufacture as long as the storage standards are respected.
Store in a covered, dry, ventilated place and away from heat sources, in environments with temperatures not exceeding 30 ° C and in an upright position.
- Handle with care. Avoid strong shocks and contact with sharp surfaces
- We recommend observing the safety rules established by Organs competent bodies and the use of appropriate PPE.
- The product should not be ingested or come into contact with the skin or eyes.
- In case of accidental ingestion, do not force vomit.
- In contact with eyes, rinse thoroughly with water for at least 15 minutes. In contact with the skin, wash well
- with soap and water and use moisturizer. Do not remove the product. Search for a doctor.
- Keep out of reach of children and animals.
- Not suitable for application in closed places, if necessary to create forced ventilation.
CATEGORIES OF PRODUCTS
Notice: Trying to access array offset on value of type bool in /home1/drykoc75/public_html/wp-content/uploads/cache/c310af7367c9988242889dfd2884a2fffe9215fd.php on line 209
Notice: Trying to access array offset on value of type bool in /home1/drykoc75/public_html/wp-content/uploads/cache/c310af7367c9988242889dfd2884a2fffe9215fd.php on line 210
